Wen 3710 10 inch Table Saw ver.2010 Manual de usuario

1

10 Know Your Table Saw A Miter Gauge G Hand Wheel B Blade Guard H Leg Stand C Table I ON/OFF switch with Safety Key D Rip Fence Scale J

11 Unpacking WARNING - to prevent accidental starting that could cause possible serious personal injury; assemble all parts to your saw before conne

12 Assembly and Adjustments WARNING! Prior to performing any assembly procedures, make sure the 10” table saw is disconnected from its electrical po

13 Mounting Table Saw to Workbench (Figure 3 & 4) If table saw is to be used in a permanent location, it should be fastened securely to a firm s

14 Mounting to Plywood (Figure 5) An alternative method of securing your table saw is to fasten the saw base to a mounting board 24" x 24"

15 90° and 45° Positive Stops Adjustment (Figure 6, 7 & 8) Warning: To prevent personal injury, always disconnect the plug from power source bef

16 Blade Parallel to Miter Gauge Groove Adjustment (Figure 9, 10 & 11) Warning: To prevent personal injury, always disconnect the plug from powe

17 16. Stand the saw on its left side and tighten the four center adjustment nuts (7, Figure 11). 17. Place the saw upright and re-check the alignmen

18 Installing the blade guard system Warning: To prevent personal injury, always disconnect plug from power source before installing or removing the

19 Installing the anti-kickback device (Figure 18) While pulling out the attachment pin, attach the Anti-Kickback Device into the flat recessed area

2 Table of Contents Technical data…………………………………………………………… 2 General safety rules……………………………………………………… 3 Additional safety rules…………………………………

20 Operation Warning: For your own safety, always observe the following safety precautions. • Never make these cuts freehand (without using the m

21 safety key removed, the switch will not operate. NOTE: If the safety key is removed while the saw is running, the saw can be turned OFF, but canno

22 Repetitive Cutting (Figure 21) REPETITIVE CUTTING is known as cutting a quantity of pieces the same length without having to mark each piece (Fig

23 Bevel Crosscutting (Figure 23) BEVEL CROSSCUTTING is the same as crosscutting except that the wood is also cut at an angle … other than 90° with

24 Maintenance For your own safety, turn switch “OFF” and remove plug from power source outlet before maintaining or lubricating your saw. Do not a

25 Trouble shooting WARNING: To avoid injury from an accidental start, turn the power switch off, remove the safety key and remove the plug from the

26 Exploded View

27 Parts List Item # Stock # Descriptions Qty Item # Stock # Descriptions Qty 1 3710-001 Sc rew 20 44 3710-044 Arbor bolt 1 2 3710-002 Motor cover

28 Item # Stock # Descriptions Qty Item # Stock # Descriptions Qty 113 3710-113 Link board 2 153 3710-153 Spring plate 1 114 3710-114 Link pin 2 1

29 LIMITED TWO YEARS WARRANTY WEN Products is committed to build tools that are dependable for years. Our warranties are consistent with this commit

3 G e n e r a l S a f e t y R u l e s The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the exp

4 N E V E R S T A N D ON T O O L OR ITS S T A N D S e r i o u s i n j u r y c o u l d o c c u r if th e t o o l is t i p p e d or if t h e c u t t i

5 Additional Safety Rules Tool Care DO NOT ALTER OR MISUSE TOOL These tools are precision built. Any alteration or modification not specified is mis

6 d. NOT ripping workpiece that is twisted or warped or does not have a straight edge to guide along the rip fence. e. NOT releasing work until you

7 spreader is in proper alignment with the saw blade. If ripping at the time, check to see if rip fence is parallel with the saw blade. Readjust as i

8 Electrical Requirements Double Insulated Tools Double Insulation is a design concept used in electric power tools which eliminates the need for the

9 IMPROPER CONNECTION of the equipment grounding conductor can result in electric shock. The conductor with the green insulation (with or without yel